Clik here to view.
DEFIV Differential Lock-Down DIY
Note: Not responsible for any damage to you or your car, this worked on my car so will work on yours. Thi kit as been tested over and over countless hours by Rick@DEFIV. If it doesnt fit you did...
View ArticleAlpina B3 Flash DIY using WinKFP
DIY Guide to Flash Alpina B3 Flash: ************************************************** ********************************** WARNING...If you dont know what your doing, dont be brave and blindly go into...
View ArticleClik here to view.
Tool32 DME fault codes list MSD80
I was checking out Tool32 trying to configure it to English for both INPA and Tool32, and finally got it working! Also I was able to use Tool32 to get all the DME fault codes in English also. I looked...
View ArticleClik here to view.
Cobb - Timing Drops / WGDC Base almost at 0 / ATR / Boost Over Shoots / Logs...
I've been wrestling with timing drops Cobb Stage 1 4.01 Aggressive OTS map. I've even tried the sport map and drive map too and get the drops to a slightly lesser extent. I've even tried all 3 levels...
View ArticleClutch + Flywheel for minimal chatter?
I am currently running around 400 awhp, and the current clutch and flywheel setup (stock) is slipping. I have heard that the DMFWs have the risk of catastrophic failure under higher power. I have no...
View ArticleClik here to view.
Meth bung shaving for flush nozzle placement DIY
Decided to do a small DIY for this since some CP have the meth bung to high and needed to b e shave so the meth nozzle can be flush with inner pipe. This DIY is done on a ER Charge pipe. This is...
View ArticleClik here to view.
Upgraded Transmission mount DIY
Note: Not responsible for any damage to you or your car, this worked on my car so will work on yours. ***This tutorial assumes you know how to get your car secured on jack stands, if in doubt do NOT...
View ArticleClik here to view.
Well hello Cobb!
Well the time had come to mix things up. I formally ran a Procede 2.5, and while it was ok it never ran the way I would have expected. After a lot of research, I decided to give COBB a shot, and boy am...
View ArticleDead Clutch Pedal after Bleeding & Clutch Swap?
Just finished installing new clutch (Spec 2+, OEM DMFW). I did this successfully in the past (ACT), but his time I released the clutch bleed valve when installing the slave cylinder (it's easier to...
View ArticleClik here to view.
cp-e Presidents' Day Exhaust/Downpipe sale
20% off any exhaust or downpipe Use promo code: LEADERS
View ArticleClik here to view.
Clutch Job.....Pilot Bearing Got Stuck on Transmission shaft !
This was one of those things that happens during a project that eats up time. I read that the pilot bearing typically sticks on the flywheel retainer but in my case it was stuck in the tranny input...
View ArticleQuick question on BMS OCC
I've recently cleaned my intake valves after 25K miles. Cylinders 1, 3 and 4 were not bad but 2, 5 and 6 were pretty gunky. Does anyone have any experience with the BMS OCC installed for around 25K...
View ArticleVishnu Single Turbo XI Edition (AWD Single)
Well it looks like Shiv is back from the hiatus and has developed an AWD single... No real information posted on the other site; or real world performance stats and it it is still a manual...
View ArticleJB4 vs COBB AP power delivery, output, etc
Could someone please educate me and others on the difference in power delivery & output between the JB4 or piggy vs COBB; so its my understanding that COBB maps adjust fueling, timing and load...
View ArticleClik here to view.
DEFIV Differential Lock-Down DIY
Note: Not responsible for any damage to you or your car, this worked on my car so will work on yours. Thi kit as been tested over and over countless hours by Rick@DEFIV. If it doesnt fit you did...
View ArticleAlpina B3 Flash DIY using WinKFP
DIY Guide to Flash Alpina B3 Flash: ************************************************** ********************************** WARNING...If you dont know what your doing, dont be brave and blindly go into...
View ArticleClik here to view.
Aquamist HFS-4, DCI and PTF tune
My car before the install was 100% stock with a Cobb PTF 94 octane tune. I'm still under extended warranty so this setup was perfect and made good power. It's crazy how just changing the software can...
View ArticleClik here to view.
Upgraded Transmission mount DIY
Note: Not responsible for any damage to you or your car, this worked on my car so will work on yours. ***This tutorial assumes you know how to get your car secured on jack stands, if in doubt do NOT...
View ArticleClik here to view.
Well hello Cobb!
Well the time had come to mix things up. I formally ran a Procede 2.5, and while it was ok it never ran the way I would have expected. After a lot of research, I decided to give COBB a shot, and boy am...
View ArticleDead Clutch Pedal after Bleeding & Clutch Swap?
Just finished installing new clutch (Spec 2+, OEM DMFW). I did this successfully in the past (ACT), but his time I released the clutch bleed valve when installing the slave cylinder (it's easier to...
View Article